Corner Radii, Internal Fillets and the Tool That Is Not in the Catalogue
- 📅 2026-11-20T10:10:52.121Z
- 👁️ 24 katselukertaa
- 🔓 Julkinen
# Corner Radii, Internal Fillets and the Tool That Is Not in the Catalogue
*By Shelly*
These remarks come from work I do with ProtoRFQ. The radius notes are general process geometry, not a tooling list for any one shop.
CAD systems are fond of sharp inside corners. A pocket is modelled with a 0.2 mm fillet, or with no fillet at all, because the solid looked crisp on the screen. A rotating tool is not a sharp corner. It has a diameter, and the corner it leaves is at least the tool radius, often larger if the tool has a corner chamfer or a wear land. When the drawing asks for a sharper corner than a practical tool can cut, the RFQ turns into a negotiation: open the radius, add a relief, change process, or accept a secondary operation. That negotiation is better held on the drawing than after a tool has already been broken in a corner.
## Write a radius that a tool can actually leave
For an internal pocket in a milled part, a good first question is: can this corner be 1.5 to 3 times the radius of a tool that will also reach the pocket depth? A 4 mm-deep pocket with a 0.3 mm inside radius implies a very small tool at a depth it may not like, especially in stainless steel or titanium. Opening the radius to 1.5 mm or 2 mm, or adding a corner relief or a dog-bone slot at the corners, often leaves function unchanged and makes the pocket a standard milling feature.
If the corner is functional — a matching male part, a seal groove, a square locating land — say so, and then choose a process that can produce it. Wire EDM, a slotting saw, a broach, or a later grind can make a sharper corner than a standard end mill. The drawing should name the functional need, not just a default fillet that happened to be in the template.
## Depth, reach and the forgotten floor radius
The floor of a pocket has a radius too, set by the tool’s end. A sharp floor corner is a similar problem in a different plane. If a mating part must sit flat on the floor and also against the wall, a floor radius will interfere unless you add a relief, undercut, or a chamfer on the mating part. Draw the relief. Do not hope the shop will invent one.
Deep, narrow pockets compound the issue: the tool that fits the width may not reach the depth with enough stiffness to hold a tight wall tolerance. If the pocket is deep and tight, consider whether it can be through, or machined from two sides, or opened slightly. A note that says “walls must be straight and parallel, floor radius 0.5 max, corners 2 mm” is a set of instructions. A model that just looks deep and sharp is not.
## External corners are a different sentence
External corners can often be sharp, chamfered, or given a small break-edge note. A large external radius that is only there because the modeller filleted everything should be relaxed to a break-edge if it is not functional; otherwise you are paying to mill a decorative radius on every part. If an external radius *is* functional (a handle, a wear surface, a matching blend), give it a size and a tolerance or a profile, and say whether a faceted mill approximation is acceptable or whether a true radius is required.
## Put the exception in a note, not in a hallway
A single sentence in the title block — “internal corner radii 2 mm unless a smaller radius is dimensioned; sharper corners are functional and must be made as drawn” — protects both sides. The shop can tool the default pockets confidently, and the few sharp corners remain visible as exceptions. If every corner is an exception, the sentence has failed and the model should be revisited.
Milling is the process that most often meets this problem first, which is why I point readers to ProtoRFQ’s [CNC milling guide](https://protorfq.com/resources/cnc-milling-guide/) when they are preparing a pocketed part, and to the [CNC milling service page](https://protorfq.com/services/cnc-milling/) when the RFQ itself is being assembled. Neither page will invent a tool for an impossible corner; they will remind you to state the geometry and the exceptions before the quote is asked to do so.
A corner radius is a process decision dressed up as a dimension. If you write a radius a tool can leave, or mark the ones no tool can leave as a deliberate process change, the rest of the drawing gets easier to trust.